Iâd been having on-and-off problems with my FAL and I think Ive ironed them out. The problem was that sometimes Iâd have the bolt ride over the next round in the mag, stopping the bolt halfway in its closeward travel and putting a nice gouge in the case that was unlucky enough to be under the bolt. I thought perhaps it was an issue of gas system adjustmentâŚperhaps more gas was needed to cause the bolt to travel more enthusiastically âŚit sorta helped but not completely. I then decided it might be an ammo problemâŚmaybe the overall cartridge length of my reloads was not long enough to assure smooth feeding â so I loaded everything out to 2.800â and still had a few probs. Magazine? MaybeâŚbut it happened with other mags too. Then I figured it out (I think). The mags I use are the used $5 mags from DSA. DSA started sending extra mag springs with them when you order them. Could the mags have weak springs and thus the cartridges are not being fed up through the magazine with sufficient force to put them in the ready position for the homeward-bound bolt? Certainly, it would mean the problem is more likely to be encountered when theres only a couple rounds in the mag rather than when the mag is full. But, theres an easier tellâŚitâs the same one you use to tell when its time to change the recoil spring in your handgun â compare an old spring to a new one. If your old one is significantly shorther than the new, swap it out. So I pulled the mag springs and compared them against the extras sent by DSA. Sure enough, they are at least a coil shorter. Swapped springs, took the mag out and loaded it with 20 roundsâŚboom, boom, boom..no problems. Tried a few in a mag that I hadnât swapped the spring out..boom, boom, nada⌠aha!
Im pretty sure thatâs the problemâŚespecially since DSA is sending extra springs with the $5 mags. Tells me theyre aware of the problem. So, I now need to pull apart 40 magazines and compare the springs in all of them. However, Iâll be glad if thatâs what the problem is. The FALâs have a reputation for reliability and I was getting worried my Springfield Armory FAL was a lemon.
Before anyone asks, I have no idea what the gas regulator is set to..no numbers on mine. But I did do the usual âturn gas off and open one step at a time until the bolt locks back on empty, then go two more notches.â
-=-=-
While weâre on the topic of guns, the recent Shotgun News has a fabulous article on the JFPO selling DIY AR-15 lowers. The âlowersâ are four pieces that are unfinished enough to not be considered firearms. You drill some holes in the conveniently placed starter indentations, thread âem, and bolt them together and you have an AR receiverâŚwith absolutely no history or paper trail. Perfectly legal since the feds do allow you to make firearms for your own personal use.
At least, you did until the ATF raided the guy who was making these things for JFPO â KT Ordnance here in Montana. Apparently, ATF knew a good thing when they saw it and couldnât have us peons with paperless ARâs.
I admire JFPO for its âin your faceâ end-run around the feds. Anyone can say theyâll fight gun registration but how many actually go far enough to start selling DIY AR kits that donât require paperwork? Another reason I like these guys better than the NRA.
Since I have no confidence in the 2008 election producing a pro-gun (or gun neutral) president, and am pretty certain itâll put in a Democrat (usually a defacto anti-gunny) my personal strategy is to start socking away AR lowers at an alarming rate. AR parts will, I think, generally always be abundant and the AR is probably a lot easier to gunplumb on your own than, say, an AK. FALs might be nice but stripped FAL receivers donât seem terribly common and the rest of the parts necessary are usually only available from one or two sourcesâŚand only really one domestically.
Needless to add, if I think itâs a wise idea to stock up on receivers before the election in 2008 you can bloody well believe I think its an even better idea to stock up on mags.
-=-=-
Speaking of boomsticks, since I have reached the point that I am confident and happy with my CZ550, its time to shift from load development to ammo production and to getting all the necessary support gear for itâŚand one of the first things that I want is a Pelican case to protect my little tackdrvier. And spare mags. I currently have just two. I need about five more. And a nice dedicated bag to carry all the gear inâŚsomething with attachment points to be carried with other gear but with straps/sling points to be carried by itself. Something that can hold ammo, cleaning kits, maybe a spotting scope, and all the other gear-driven goodness that you need when putting the sneak on something 600 yards away. I likes my .308, I do.
-=-=-
Got the new rack and bag for the mountain bike today. Also picked up a foot-powered pump. Additionally, I need to pick up a more compact pump to carry with the bike and I also want a 12v pump for use at the house. (Which can be used for several other thingsâŚlike inflating those funky little inflatable guest beds, filling vehicle tires and pressurizing homebuilt flamethrowers.) Still need a fair amount of support gear for my bicycle but itâs a fairly low priority at the moment. The basic gear will be fine for nowâŚIâll get a spare wheel, spokes, chain, etc. at a later date. With gas around $3 a gallon it just doesnât make sense to jump in the truck to go pick up the mail or a 12-pack of Coke. Plus, as local cops have opined, guys on bicycles are harder to catch than guys in vehiclesâŚand me, Im all about the options. Still wouldnât mind getting the frame powdercoated thoughâŚâŚâŚ.

